Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterWhy Calabasas Homeowners Choose Ghost Controls Gate Repair
Ironworks Gate Co. provides Calabasas Ghost Controls service across the area, from the gated estates along Mulholland Highway to the HOA communities of The Oaks and Calabasas Park. We’re not authorized by Ghost Controls, and we say that plainly, but our technicians work on their openers daily and carry an independent bench-tested library of Ghost Controls circuit boards, limit switch assemblies, and actuator parts that most generalist repair shops simply don’t have. If your AXDP dual gate has lost its sync or a DTP arm stops mid-travel, we fix it in one visit and back the work with our written 90-Day Done Right Promise. Call (747) 308-3262 and a live person answers, any hour, any day.
Why Trust Ironworks Gate Co. for Your Ghost Controls Gate Repair?
Ghost Controls openers are solid machines, but they have quirks, and the difference between a fix that holds and one that fails again in three months comes down to whether the technician has seen that particular failure before. Our crews have. Victor Salinas, our owner and lead gate technician, grew up in the Las Virgenes corridor just off Mulholland Highway and spent years diagnosing gate motors on Calabasas driveways before he trained his first apprentice. He says it plainly: if the gate is giving you trouble, there is a reason, we just have to find it.
What that means for your Ghost Controls system is specific. We know the AXDP series dual openers that Calabasas homeowners installed in the 2000s, and we know how the dry, dusty Santa Ana seasons wear out their actuator micro-switches faster than the manufacturer’s generic service literature suggests. We know the DTP single-swing units common on pedestrian gates, and we stock the limit switch assemblies they need when the “gate closed” signal won’t clear. We keep OEM Ghost Controls boards and actuators on the shelf, and for discontinued models we use quality aftermarket gears and relays that match or beat the originals. Every job is warranty-safe, priced before we turn a single bolt, and covered by our written 90-Day Done Right Promise.
Common Ghost Controls Gate Repair Problems We Fix in Calabasas
These are the failures we see most often on Ghost Controls systems in Calabasas, and they line up with our local conditions more than the generic forum threads would have you believe.
- AXDP dual-gate synchronization drift. One leaf opens a second or two before the other, then the second jerks awake. In Calabasas, this is frequently caused by dry dust and heat working into the actuator limit switch, which fails to report its position accurately. We replace the switch with an OEM Ghost Controls limit assembly and recalibrate both arms so the leaves move as one unit again.
- DTP/AXDP actuator arm stopping mid-travel or reversing randomly. That is the classic worn micro-switch failure inside the actuator. The gate starts fine, then pauses or backs up because the switch sends a false signal. It is a specific repair, not a full opener replacement, and we complete it the same day in most cases.
- AXXESS keypad relay chatter. Keys don’t register reliably, or the gate opens without a full code. The AXXESS wireless keypad relay develops contact chatter, and in Calabasas the coastal morning moisture that rolls up the canyons makes it worse. We open the keypad, clean or replace the relay contacts, and seal the housing against the next damp season.
- Solar TSS1 low-voltage resets on hot afternoons. The TSS1 solar kit works well until summer, when the undersized battery wiring on some installations can’t carry enough current and the controller resets mid-cycle. We rewire with proper gauge, confirm the panel output, and the resets stop. This is common on off-grid and remote Calabasas ridge properties.
- “Gate obstructed” warnings every few weeks with nothing stuck. The Ghost Controls app throws this when the motor’s current sensor drifts out of calibration, usually after sustained wind loading on the gate. Calabasas gets intense Santa Ana gusts in fall and winter that push the gate hard, and the sensor learns the wrong baseline. We recalibrate the force settings and check the hinge posts for the wind damage that usually started the problem.
Ghost Controls Parts & Our Repair-vs-Replace Approach
We stock OEM Ghost Controls boards, actuators, and limit switch assemblies for the current DTP and AXXESS lines, which keeps most Calabasas jobs same-week. For aged or discontinued AXDP and DTP units, we use quality aftermarket gears, relays, and motor brushes that match or exceed the originals, and we tell you before we install them what we’re using and why. No surprises on the bill, and no mystery parts.
Our stance on repair versus replace is the same one we would give a neighbor. If a 15-year-old AXDP has a failed motor and the gearbox shows wear, we will not patch it twice. We’ll quote a motor replacement honestly, explain the cost of continuing to repair an aged opener versus putting in a new unit, and let you decide. You get the numbers up front, agreed in writing before work starts. Call (747) 308-3262 and we’ll talk it through with you.
Our Ghost Controls Service Process - Step by Step
- 1
Diagnosis. We arrive, listen to what the gate is doing, and test the Ghost Controls controller, actuator, and limit circuits directly. We read the fault codes and test the components rather than guessing from the symptom alone.
- 2
Repair or install. We complete the work with OEM or quality aftermarket parts as agreed, including motor installation, battery backup wiring, or keypad replacement. For dual AXDP gates, we always recalibrate both leaves so they cycle in sync.
- 3
Testing. We cycle the gate under load, check the force settings, verify the obstruction sensor, and test the keypad and remotes. We run it hard before we call it done.
- 4
Warranty. Every completed job is covered by our written 90-Day Done Right Promise. If it is not right, we come back and make it right, no paperwork, no arguing.
Ghost Controls Products We Service & Install in Calabasas
Our technicians work on the full Ghost Controls lineup you will find on Calabasas driveways: the AXDP series dual gate openers, the DTP single-swing openers used on pedestrian gates and smaller driveway gates, the AXXESS wireless keypad and remote kits, and the TSS1 solar opener for off-grid properties. We also handle motor replacement, battery backup installation, and Gate Repair on all of these systems. If you have a Ghost Controls unit and it is not behaving, call (747) 308-3262 and describe what you’re seeing. We will tell you whether it sounds like a simple fix or something worth scheduling a visit for.
We Also Service These Brands
Ghost Controls is one of nine gate-automation brands our technicians are trained and equipped to service. We also work on LiftMaster, Mighty Mule, DoorKing, FAAC, BFT, Linear, Viking, and Elite. Whatever is mounted on your driveway, we have seen it before.
FAQs - Ghost Controls Gate Repair Service in Calabasas
The second leaf is hesitating because its actuator limit switch is worn or dirty, and it is not reporting position correctly to the controller. In Calabasas, the dry dust and heat we get during Santa Ana season accelerates this wear. The fix is an OEM Ghost Controls limit assembly replacement and a recalibration of both actuator arms, which we complete in one visit. Call (747) 308-3262 for a free estimate.
No, it is not normal. That blinking means the controller is not receiving a clean closed-position signal from the limit switch. The gate closes, but the electronics do not know it. It is usually a failing limit switch or a misaligned magnet, and left alone it will eventually stop closing entirely. We fix it same-week with OEM parts.
Yes. Ghost Controls battery backup kits can be added to most AXDP and DTP systems after the fact, and we install them regularly in Calabasas where power outages during wind events can leave a gate stuck. The install includes proper wiring and a load test so you know the backup will actually hold when the power fails.
That is almost always relay chatter inside the keypad, made worse by thermal expansion in the afternoon heat. The keypad registers the key press but the relay contact does not close cleanly, so the controller never gets the open command. We clean or replace the relay and reseal the housing, and the keypad works consistently again.
The motor’s current sensor has drifted out of calibration, likely after the gate was pushed hard by wind. Calabasas sees strong Santa Ana gusts in fall and winter that load the gate and confuse the sensor’s baseline. We recalibrate the force settings and check the hinge posts, because the wind that confused the sensor usually bent something too. Call (747) 308-3262 to schedule a diagnosis.
Ghost Controls repair costs in Calabasas vary by the part and the labor involved. A limit switch replacement on a DTP or AXDP actuator typically runs $220 to $340. A full actuator replacement falls between $380 and $600 depending on the model and whether the gate is single or dual leaf. Keypad relay repair runs $140 to $200, and a motor replacement on an older AXDP can range from $450 to $700. Every quote is agreed in writing before work starts, and we offer $50 off any repair over $250 plus a 5% senior and veteran discount. Call (747) 308-3262 for an exact quote, estimates are free.
Book Your Ghost Controls Service in Calabasas, CA
Call (747) 308-3262 and describe what your Ghost Controls gate is doing. A live person answers 24 hours a day, 7 days a week. We will schedule a visit, quote the price up front, and stand behind the work with our written 90-Day Done Right Promise.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Calabasas since 1984.