FAAC Gate Parts & Welding Nationwide

FAAC Gate Parts & Welding in Calabasas: What to Know First

We provide independent FAAC gate parts and welding in Calabasas, with most hinge, post, roller, and latch repairs completed in a single visit. A typical FAAC structural or parts job runs $240 to $890 depending on the damage, and every quote is settled before we touch a bolt. If your FAAC gate is sagging, grinding, or refusing to latch, call (747) 308-3262 and a live person will answer.

Call (747) 308-3262

This page is for Calabasas homeowners who own a FAAC automated gate, know the brand, and want straight answers about parts, welding, and what actually fails in our foothill climate. We are an independent FAAC service provider, not an authorized dealer, which means we can source both OEM and quality aftermarket parts without pushing one over the other. Victor Salinas, our owner and lead technician, has spent decades working on FAAC units throughout Calabasas, Hidden Hills, and the Las Virgenes corridor.

How FAAC Products Fail - and How We Fix Them

FAAC builds a strong operator. The mechanical parts around it, hinges, posts, rails, rollers, latches, take the real beating. Here are the failures we see most often in Calabasas.

• 414 and 415 series hinge wear on heavy driveway gates. These are the workhorse FAAC models on estate entrances throughout Calabasas. The operator gets blamed when the gate starts sagging or reversing, but the real cause is often a worn bottom hinge carrying fifty extra pounds because the top hinge was never shimmed after the post settled. We strip, rebuild, or replace the hinge and re-set the post alignment before touching the operator.
• Post fatigue at the weld plate on S418 and S450 slide gates. Slide gate posts in Calabasas take lateral force every cycle, and after years of dry and hot Santa Ana seasons, the weld at the base plate can fatigue. We see this on FAAC slide applications more than on swing units. The fix is cutting out the failing weld, re-seating the post, and laying a full-penetration weld, not just a surface bead.
• Rail deformation from roller bite. FAAC slide gate rails are designed to spec, but if the rollers were installed a few degrees off, the rail wears unevenly and eventually grooves. Owners hear a rumble and assume the motor is failing. We correct the roller alignment, weld and grind the rail face smooth, and the gate runs quiet again.
• Latch and lock misalignment on C720 and C721 swing operators. These are popular FAAC swing units on Calabasas driveways. When the gate and the mechanical latch grow apart, usually from hinge sag or post movement, the operator keeps cycling against a latch that does not fully release. We realign the latch assembly and rebuild the hinge, which stops the repeated motor strain.
• Weld cracking at the gate frame corners. Ornamental FAAC gates in Calabasas often have steel frames with decorative infill. Over time, corner welds crack from repeated cycling, especially where infill has loosened against the frame. We grind out the old weld, lay fresh material, and reinforce the joint so the gate does not twist.

The pattern is simple. FAAC electronics and motors are rarely the first thing to fail. The metal around them gives out first, and fixing the metal correctly keeps the operator healthy.

Our FAAC Gate Parts & Welding Process

1. 1
   Call and talk to a person. You reach a live dispatcher at (747) 308-3262. We note the FAAC model, the symptom, and whether the gate is stuck open, stuck closed, or just not right.
2. 2
   On-site assessment. Our technician arrives in a fully stocked truck, checks the operator, hinges, posts, rails, rollers, and latch. We write down what we find and show you the damage before we quote.
3. 3
   Upfront quote. We settle the price before any work starts. You know the number, the parts we will use, and the time it should take.
4. 4
   Parts decision. For FAAC repairs we explain the choice between OEM FAAC parts and quality aftermarket equivalents, including price and longevity. We never hide what we are installing.
5. 5
   Welding and mechanical repair. We do the structural work first, re-align everything, then re-test the operator cycle. The gate gets the full treatment, not just the visible symptom.
6. 6
   Test, explain, guarantee. We cycle the gate ten or fifteen times while you watch, explain what we fixed and why, and leave you with the written 90-Day Done Right Promise.

Most FAAC parts and welding jobs in Calabasas are done inside of two hours on site. The truck carries common FAAC hinge, roller, and latch hardware, plus the welding rig for structural work.

What FAAC Gate Parts & Welding Costs in Calabasas

Here are the numbers we typically quote on FAAC work in the Calabasas area. Prices depend on gate weight, post condition, and access. You will always get an exact price before we begin.

• Hinge replacement, single gate: $240 to $520
• Post straightening and re-weld: $380 to $760
• Slide rail repair and resurfacing: $320 to $650
• Latch and lock realignment: $180 to $390
• Custom welding, cracked frame repair: $260 to $890
• Roller replacement with rail adjustment: $280 to $540

The cost moves with two things: whether we are rebuilding a part or replacing it, and whether the post or rail has to be dug out and reset. A hinge that just needs new pins and shims costs less than a post that broke at the base plate. Estimates are free, and the price we quote is the price you pay. Call (747) 308-3262 and we will come look.

Why Calabasas Homeowners Call Ironworks Gate Co. for FAAC Work

We have been welding and repairing driveway gates for over 42 years, founded in 1984 in the Calabasas area. We understand what FAAC owners in this community need because we have worked on their gates, their neighbors’ gates, and the gates their kids now own.

Every job is backed by the 90-Day Done Right Promise, a written guarantee with no paperwork and no arguing. If it is not right, we come back and make it right. Every time.

We also service the other brands we see on Calabasas driveways, LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if you have multiple gates or change a motor later, we handle it. Our technicians are background-checked, uniformed, and trained on nine gate-automation brands. One visit, correct diagnosis, honest price. That is the whole job.

FAQs