Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Motor & Opener in Calabasas: What to Know First
Linear gate motor and opener repair in Calabasas typically runs between $225 and $480 for most board, limit switch, and gear replacements, with full motor swaps landing between $900 and $1,600 depending on the model and how much of the existing rail and arm hardware can be reused. We complete most Linear gate motor & opener service calls in a single visit, and the price is settled before any work begins. This page is for Calabasas homeowners whose Linear opener has quit, gotten loud, or started stopping halfway, and who want a straight answer about what it costs and what it takes to fix it. Call (747) 308-3262 and a live person answers, day or night.
How Linear Products Fail - and How We Fix Them
- Linear LDO series (LDO50, LDO33) control board capacitor failure. These swing-gate actuators run hot in Calabasas summers, especially on south-facing columns where the housing bakes all afternoon. The first sign is usually a gate that opens fine in the morning but won’t respond by mid-day. The board’s electrolytic capacitors dry out and the motor won’t get the start signal. We replace the board with either a Linear OEM unit or a quality aftermarket board that’s been run on local benches, and we add a vented column bracket where it helps. Repair runs $275 to $420.
- Linear slide-gate chain and idler wear on the SL and GSL series. Calabasas properties with long driveways put a lot of travel cycles on a slide motor, and the idler sprocket behind the chain wears oval before the motor itself shows any strain. Owners hear a rhythmic clacking, then the gate starts jerking. We replace the idler sprocket, reset the chain tension to factory spec, and check the rail for flat spots. A sloppy chain will kill a new motor in a year, so we address both in the same visit.
- Limit switch drift on older Linear APeX and MegaCode actuator arms. Mechanical limit switches on Linear arms that are ten years or older will creep every few months, and the gate either doesn’t close all the way or thumps hard against the stop. We set the limits, confirm the auto-close now works as the original install intended, and in some cases retrofit magnetic limit kits that hold position longer. This is a quick fix, typically under two hours, usually $140 to $190.
- Remote and receiver mismatch on Linear Multi-Code systems. Linear made the Multi-Code and MegaCode lines for years, and the receiver dip-switch settings are easy to bump during a battery change in the remote or a power blink. Homeowners call us thinking they need a whole new motor when the receiver simply lost its code. Before quoting any opener replacement we always verify that the receiver is still matched to the remote, which saves Calabasas customers hundreds of dollars a year in misdirected replacements.
- AC to DC conversion fatigue in the Linear gate operator power supplies. Our techs see the bridge rectifier in Linear power supply units go soft after years of voltage fluctuation along the local grid leg that runs up Las Virgenes. The motor hums, rocks, and won’t pull the gate. This job involves pinpointing whether it’s the power supply or the actual motor winding before throwing parts at it. Victor Salinas has tested enough Linear operators on Calabasas properties to usually have that answer in the first fifteen minutes of the call.
Our Linear Gate Motor & Opener Process
- 1
We listen, then we look. When you call, we ask what the gate does when it fails and when it started. Then the tech walks the whole gate before touching a screwdriver: hinges, chain, rail, column, and the motor housing.
- 2
We diagnose the Linear unit specifically. We check live voltage at the operator, test the board for output, and confirm the receiver and limits before quoting anything. If the problem is the Linear motor and opener, we say so plainly; if it’s the hinge, we say that instead.
- 3
We give you the number before work begins. You hear the price, the part, and the expected time, and you approve it first. No invoice later that looks different from the quote.
- 4
We make the repair with the right part. We use Linear OEM parts when they’re available and priced reasonably, and proven aftermarket parts when warranty or lead time make them the better honest choice.
- 5
We test it through every cycle. We run the gate open-close, auto-close, obstruction test, and remote range. We adjust force and limit settings so the gate runs as smoothly as Linear’s engineers intended.
- 6
We leave it clean and write the guarantee. Tools up, gate wiped down, and the 90-Day Done Right Promise written on the invoice. If it’s not right, we come back.
What Linear Gate Motor & Opener Costs in Calabasas
- Limit switch adjustment or reset: $125 to $190
- Control board replacement (LDO series): $275 to $420
- Power supply replacement: $190 to $310
- Chain and idler sprocket replacement (slide gates): $350 to $575
- Full Linear motor and opener replacement: $900 to $1,600
The big variable is which Linear series you have and whether the existing mounting hardware, rail, and wiring can be reused. Calabasas gates with columns built in the 1980s and 1990s often need a bolt pattern adapter for newer Linear motors, and that’s a small parts line item. We quote all of it before we start. Call (747) 308-3262 and get a number you can hold us to.
Why Calabasas Homeowners Call Ironworks Gate Co. for Linear Work
We’ve been working on gates in this area for over 42 years, and we’ve opened more Linear operators at Calabasas addresses than we can count. We’re an independent Linear service provider, which means we recommend what actually works best for your gate, not what a manufacturer says we have to sell. If a Linear motor is worth repairing, we repair it. If it’s done, we tell you honestly and show you the numbers for a replacement. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if you ever switch brands or have a second gate on the property, we handle it. Every job gets the 90-Day Done Right Promise in writing, and every phone call gets a live person, 24 hours a day.
FAQs
Most Linear gate motor & opener calls in Calabasas are scheduled the same day or the next morning, and we can often complete the repair that day because our trucks carry Linear boards, limit switches, and remotes on board. Call (747) 308-3262 for a live answer and a real arrival time.
We use Linear OEM parts whenever they’re available at a fair price, and we’ll tell you upfront which part is going in and why. On older Linear models where factory parts are discontinued, we use aftermarket parts that we’ve tested on local Calabasas gates and trust to hold up.
As a rule, if the Linear motor itself is still pulling cleanly and the issue is a board, limit switch, capacitor, or receiver, repair is the right call and usually costs under $500. When the motor windings are gone or the gear reduction is failing, replacement makes more sense. We’ll show you what we see and give you the repair number and the replace number side by side before you decide.
Yes, every Linear gate motor & opener repair we complete in Calabasas is covered by our 90-Day Done Right Promise, written on the invoice. If it’s not right, we come back and make it right. No paperwork on your end, no argument, no exceptions.
On many Linear gate operators, especially the LDO series and older MegaCode arms, the control board capacitors begin to fail when column temperatures climb above 100 degrees, which is common in Calabasas from July through September. The fix is typically a board replacement rather than a motor replacement. If your gate is giving you trouble, there is a reason - we just have to find it.
Written by Victor Salinas, Owner & Lead Gate Technician, Ironworks Gate Co. at Ironworks Gate Co., serving Calabasas and nearby areas.