Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Welding & Fabrication: The Calabasas Owner’s Guide
We stock and install Linear-compatible gate welding and fabrication parts across Calabasas, Agoura Hills, and the surrounding foothill communities, with most bracket, hinge, and mount repairs completed on the first visit. A typical Linear welding or fabrication repair in this area runs $220-$480 installed, including the replacement part, the weld itself, and on-site cleanup. Homeowners usually discover the failure the hard way: the gate starts dragging on the concrete, the opener strains against a broken mount, or a hinge finally tears away from the post after years of dry-season expansion and contraction.
We’re an independent gate company, not affiliated with Linear, but we’ve been matching their parts to the right models for decades. If the gate is giving you trouble, there is a reason - we just have to find it.
Which Linear Models This Applies To
Linear’s residential gate openers have been through several generations, and the welding and fabrication needs shift with each one. The most common Linear openers we fabricate mounts and hinge brackets for include the LRA series, the GTO/PRO line (after Linear acquired GTO in the mid-2000s), and the APeX and LCO series operators that run many of the swing gates in Calabasas’s Mulwood, Vista Point, and Mountain View Estates neighborhoods.
Here’s the compatibility gotcha that catches people: the bolt pattern on a Linear LRA mount bracket is not the same as the pattern on a GTO/PRO bracket, even though both say “Linear” on the housing. We measure the center-to-center mounting holes before we ever cut a plate. Your gate’s weight determines the bracket gauge we fabricate - a 14-foot driveway gate on a hillside in Calabasas Park needs a heavier plate than a 9-foot walk gate on a flat lot, and we size accordingly. For owners who want OEM, we can order it and install it. But for most welded brackets and hinge reinforcements, a properly fabricated steel plate matched to your opener’s bolt pattern holds up better than the original cast part, especially through the Santa Ana wind cycles that torque gates off their mounts every fall.
Signs Your Linear Welding & Fabrication Is Failing
- It takes two or three tries for the opener to move the gate. The mount plate has cracked or shifted, so the motor is pushing against slop instead of steel. The opener keeps running, but the force goes into the crack, not the gate.
- You hear a clunk or a grind right before the gate moves. A broken weld on the hinge bracket lets the gate drop a half-inch before the motor gets traction. That clunk is the gate falling onto the remaining bracket, and it gets worse every cycle.
- The gate sags visibly at the far end. The hinge side has compromised welds, and the weight of the gate is now resting on the opener arm instead of the post. This is how Linear operators burn out their gearboxes early.
- You can see daylight through the mount or a crack that follows the old weld line. Powder coat hides a lot, but a hairline crack that runs along the edge of a bracket means the metal is fatigued. It will not heal.
- One hinge is rusty while the rest of the gate still looks clean. Water is pooling in a cracked weld and working its way under the finish. In Calabasas’s dry climate, that rust does not wash away - it sits there and eats through until the hinge lets go.
Replacement Cost & What’s Included
For Linear gate welding and fabrication in Calabasas, a straightforward hinge rebuild or mount-bracket replacement typically runs $180-$320 installed. A full hinge-set rebuild with fabricated reinforcement plates on both posts runs $350-$480, and custom fabrication for an unusual mount or an older Linear model that needs a one-off bracket runs $400-$600 depending on the steel we need to cut and the access at the job site.
Every price we quote includes the fabricated part, the welding labor, on-site grinding and cleanup, and a test cycle of the gate so we know it closes square before we leave. We settle the price before we pick up a torch - no surprises on the bill. And the work itself is covered under our written 90-Day Done Right Promise: if it is not right, we come back and make it right, every time.
DIY or Call Us?
Some things you can reasonably check yourself: look at the hinge welds with a flashlight and see if a crack runs along the old weld line, and watch the mount bracket while the gate cycles to see if it flexes. That tells you what to tell us when you call. But actually repairing a torn hinge or a cracked operator mount is not a weekend job. You’re working with a gate that can weigh 400 pounds or more, often on a slope, usually under tension from the opener. A bad weld on a load-bearing bracket will look fine for a month and fail exactly when the gate falls toward someone.
We weld these repairs with the gate blocked, the opener disengaged, and the bracket re-aligned before the first tack. If you’re in Calabasas and the weld is cracked or the gate is dragging, call (747) 308-3262 and we’ll give you a straight answer over the phone.
FAQs
On a properly set gate in Calabasas’s dry climate, a well-fabricated, correctly welded steel bracket should last 10-15 years before fatigue becomes a concern. The original OEM cast brackets rarely last that long through Santa Ana cycles, which is why we fabricate replacements from heavier plate. Call (747) 308-3262 if you want us to look at what you have before it fails.
Sometimes, and we will tell you honestly which one makes sense. A small crack on a low-stress area can be ground out and re-welded. A crack on a load-bearing hinge or opener mount usually means the metal is fatigued, and welding over it just moves the failure to the next inch of plate. We will quote you the repair, not the upsell.
Most hinge and bracket repairs are done in one visit, usually within an hour and a half to three hours on site, depending on how much we need to fabricate and how the access looks at the driveway. If we need to pattern a one-off bracket for an older Linear model, we’ll fabricate it at the shop and come back to install it, and we’ll tell you that upfront.
We carry common Linear mount brackets, hinge kits, and opener arms on the truck, and we fabricate custom brackets in-house when a stock part will not hold up. We also keep parts for LiftMaster, Mighty Mule, and Ghost Controls, and we are trained and equipped on nine gate-automation brands, so the correct fix is made on the first visit, whatever is on the driveway.
Yes. Every weld and fabricated part we install is covered under our written 90-Day Done Right Promise. If a weld we made fails inside 90 days because of our workmanship, we come back and fix it at no charge - no paperwork, no arguing. We stand behind it.
Get a Free Estimate in Calabasas
If your Linear gate is sagging, dragging, or groaning on its hinges, call Ironworks Gate Co. at (747) 308-3262. A live person answers 24 hours a day, seven days a week. We will talk through what you’re seeing, give you an honest range over the phone, and schedule a visit when it works for you. Background-checked, uniformed technicians, upfront pricing settled before we start, and work that’s done right and backed in writing.
Written by Victor Salinas, Owner & Lead Gate Technician, Ironworks Gate Co., serving Calabasas and nearby areas.